![]() Always turn off power to the air conditioning or heating system prior to installing, removing, cleaning or servicing thermostat.This thermostat is a dual power thermostat and either requires 24 Volts AC Power or two (2) properly installed “AA” alkaline batteries for normal operation and control of the heating or cooling system.Malfunctions covered after the manufacturers warranty. Refer to “Low Battery Detection and Replacement” section for more information. Proselect Thermostat Troubleshooting proselect thermostat psts11p52 instructions printable pro select psts11p52 programmable hvac thermostat proselect thermostat manual psts11p52 share. This thermostat also requires two (2) properly installed “AA” alkaline batteries to retain clock setting in the event of loss of AC Power due to a power outage or rolling blackouts when used as a hardwired thermostat.This thermostat should only be used as described in this manual.Electrical Rating: 24 Volt AC (18-30 Volt AC) 1 amp maximum load per terminal 2 amp total maximum load (all terminals) (PSTS11P52) 3 amp total maximum load (all terminals) (PSTS21P52).Īny other use is not recommended and will void the warranty.DC Power: 3.0 Volt DC (2 AA Alkaline batteries included).Replacing Existing Thermostat Most thermostats have three parts: The cover, which may snap or hinge over the existing thermostat.The electronics or body, which controls the existing system.The sub-base, where the wires attach through the wall to the existing system.Always turn off power to the air conditioning or heating system prior to removing existing thermostat. Carefully remove the cover and electronics body from the old thermostat sub-base. Depending on the brand, these parts may pull off or need to be unscrewed. The old sub-base should remain wired and on the wall until steps 4 and 5. ![]() Label every old wire with the letter of the connection to which the wire is attached. Depending on the brand of the old thermostat, your letters may be different. After labeling the old wires, loosen each connection and remove them from old sub-base. Secure the wires to prevent them from slipping into the hole in the wall. ![]() Remove the old sub-base from the wall, again being careful that the wires do not slip into the hole in the wall. Use the chart below to determine the new thermostat connections. As an example, if the old thermostat had a G connection, it goes to G on the new thermostat. Note the chart includes information for Proselect® PSTS11P52 and PSTS21P52 thermostats. Old Terminal from New Terminal for New Terminal for Existing Thermostat New Thermostat New Thermostat (PSTS21P52) (PSTS11P52)Ĭooling Transformer Heating Transformer 24 VAC Reversing Valve (Heating) Reversing Valve (Cooling) Cooling or Compressor for HP System 1st Stage Heat or Emergency Heat Fan Control 24 VAC Common 2nd Stage Heatġ.īe sure to use the correct column for the new thermostat. Download proselect 2019r2.12.Press the HOLD button to bypass the program schedule. Thermostat location air why conditioning bci manager indoor february Pacemaster manual proselect owners treadmill plus pro console Thermostat Testimonial - YouTube Your Thermostat Location Matters: Here's Why Manual honeywell visionpro heating central Establishing A Need - Thermostat - YouTube Pacemaster Proselect Owners Manual - Bicycleupload Honeywell manual programmable thermostat operating appliance Download ProSelect 2019r2.12 proselect HONEYWELL VISIONPRO_TH8000 Central Heating Download Manual For Free Now Proselect thermostat manual webmanual eng Manual - Honeywell Thermostat CT3200 | Thermostat | Battery (Electricity) thermostat honeywell manual Honeywell RTH6300B Programmable Thermostat Operating Manual Proselect PSTS11P52 And PSTS21P52 | Thermostat pt. 9 Pics about Proselect PSTS11P52 and PSTS21P52 | Thermostat : Proselect PSTS11P52 and PSTS21P52 | Thermostat, Download ProSelect 2019r2.12 and also Manual - Honeywell Thermostat CT3200 | Thermostat | Battery (Electricity). ![]() Proselect PSTS11P52 and PSTS21P52 | Thermostat.
0 Comments
Leave a Reply. |